Hell-bent-steel 1994-2012 Dodge Ram Solid Axle 4X4 Front Anti-Sway Manuale Utente Scaricare il pdf

150-000-1001

05/2011

HELL BENT STEEL, INC - INSTALLATION INSTRUCTIONS

FRONT ANTI-SWAY BAR DROP BRACKETS, END LINKS, AND BUSHINGS FOR

1994-2011 DODGE RAM SOLID AXLE 4X4

YOU CAN ALSO VIEW THE INSTRUCTIONS ON LINE AT www.hellbentsteel.com

IMPORTANT NOTES:

Please read before beginning installation. OEM Manual

should be used as a reference.

It is highly recommended that a certified

mechanic perform this installation.

Read and understand all the instructions before

beginning installation. Use Loctite® on all bolts

associated with this installation.

Torque Settings:

• Anti-sway bar bushing to frame bolts: 10mm, 45 ft-lbs

• Drop bracket to frame bolts: 10mm, 45 ft-lbs

• End link frame nut:

o HBS-SMX-1224, 1225, 1227, 1311: 60 ft-lbs

o HBS-SMX-1226: 40 ft-lbs

Drop Bracket Installation:

The goal of the drop brackets is to keep the sway bar end-links in their stock (vertical) position.

Doing so will avoid any excessive wear on the end-link bushings and extend the life of the end-links. After your

leveling kit is installed, check the angle position of the end-links. If the end-links are leaning either forward or

backward then use the drop brackets to adjust the end-links to the vertical position. If the end-links are vertical

without the drop brackets, then you do not need to install the drop brackets. Installing drop brackets when they

are not needed can cause excessive wear on the end-link bushings and reduce the life of the end-links.

1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can not roll.

2. With a 15mm socket or end wrench, remove the four (4) 10mm bolts that mount the anti-sway bar to the frame.

NOTE: The anti-sway bar will swing free when the bolts are removed. Be sure to support the bar to avoid injury and

excessive load on the end-links.

***If only installing the anti-sway bar drop brackets skip to step 5 ***

Anti-Sway Bar Bushing Installation:

3. Remove the stock bushing and bracket from

the anti-sway bar. Remove any dirt, rust, or scale.

4. Grease the inner diameter of the bushing and

the contact area of the anti-sway bar before

installation. Install new bushings and brackets on

to the anti-sway bar. Rotate the anti-sway bar up

and down while holding the brackets to disperse

the grease.

NOTE: For periodic maintenance, each bushing

requires three full pumps of a grease gun to

insure proper lubrication.

1 2

Sommario

Pagina 1 - Drop Bracket Installation:

150-000-1001 05/2011 HELL BENT STEEL, INC - INSTALLATION INSTRUCTIONS FRONT ANTI-SWAY BAR DROP BRACKETS, END LINKS, AND BUSHINGS FOR 1994-2011 DODGE

Pagina 2 - 150-000-1001

150-000-1001 05/11 5. Bolt the anti-sway bar drop brackets to the bushing bracket on the anti-sway bar using the 10mm bolts, nuts, and washers provi

Commenti su questo manuale

Nessun commento

Hell-bent-steel 1994-2012 Dodge Ram Solid Axle 4X4 Front Anti-Sway Manuale Utente

Navigare online o scaricare Manuale Utente per Per l'auto Hell-bent-steel 1994-2012 Dodge Ram Solid Axle 4X4 Front Anti-Sway. Hell Bent Steel 1994-2012 Dodge Ram Solid Axle 4X4 Front Anti-Sway Bar Drop Brackets, & End Links User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Hell-bent-steel 1994-2012 Dodge Ram Solid Axle 4X4 Front Anti-Sway